Known as the “Flying Tank” by her pilots, the Mil Mi-24 is arguably the best Russian attack helicopter ever build. Having made her first flight in September 1969, this machine served the USSR predominantly during the Cold War. However, many are still being used to this day by the Russian Air Force and many other countries. Despite the fact that she’s still being flown, most of the 2300 build were discarded at the end of the Cold War. This resulted in many helicopters being dumped at local airfields and parking lots where they were left to the elements. Slowly, but inevitably, they turned to rust and bones…
Though being a very sad story for all these flying tanks, they do make for great subjects for model builders. So when I was in need of a break with the BK-117 project, it didn’t take me long to buy the Trumpeter kit and quickly got going with this one.
Kit by Trumpeter
This project started on May 25, 2015 and was finished on 04 June 2016.
Photos of this project can be found here:
The last 0.01%
04 Sept. 2016 | Sumburgh, UK | By Niek Nijsen
More than a year later since the last post... Finally, after collecting the base board from Lyle in May during my holiday in Florida, I've been able to complete this project.
With the stand now in my workplace, I could get back to work. First I masked the edges with tape. I then mixed the plaster so that it could still be poured. Using a wooden stick that was long enough to cover the whole width of the base, I levelled the plaster to form the concrete runway. The few bits that suck to the stick actually engraved the concrete with lines like the real Russian airfields tend to have. A lucky coincidence.
Once the plaster was hard, I used a blunt knife and modelling tools to create the cracks and weathering damage. I sprayed the whole with grey primer before using different grey tones, washes and pigments to give the base its final colour composition. A black wash was used to create the oil stains. After letting the paint dry for a day or so I added all the grass, moss, and fencing. The water was created with “Woodlands Realistic Water” and is resin based.
The Hind was added to the diorama and glued in place before receiving a few bushes and water around the wheels. Next up I added the blades and other items that are laying around the helicopter. Initially I had the cockpit-door closed, but after a few people suggested it, I opted to open it to allow a view inside.
And that’s basically it, not much more to it. I think the photos in “The Making Of” gallery will explain the rest.
Thank you for following me on this build and your support throughout. It’s been a real pleasure.
“Forgotten Souls” is now officially finished.
06 Aug. 2015 | Sumburgh, UK | By Niek Nijsen
So, it seems the Hind project has come to an end. Although, that's for 99.9%. The stand still needs to be made, but Lyle is working hard on this. Once it has arrived here, I'll be able to finish the project for the full 100%.
To be honest, not a whole lot has happened in regards to the Hind project, as she was already almost finished. The rotorblades have been painted as well as the rotorhub itself. I've been working a bit on the diorama layout and used a piece of cloth to act as a cover for some of the parts which will be laying around the heli. The biggest problem was attaching the rotorhead as it's completely out of balance due to the 2 missing blades. I ended up drilling a hole in both the hub and heli to fit a cocktail stick. This holds the blades in place nicely without bending or breaking.
The next update will be later this year when I'll begin working on the stand. As always, photos in the link to the right. Until then!
05 Jun. 2015 | Kibworth, UK | By Niek Nijsen
Another build?! Yes, another build indeed. I really needed a break from the BK-117 project after 300 hours and hardly any progress. So there I was, thinking what to build this time. It needed to be something that would be finished in a rather short period of time. Having come across photos of abandoned helicopters in Russia after the Cold War, I quickly found my new subject. The model would predominantly be made straight out of the box, although the interior could do with some extra details, thus I added the Verlinden kit as well. Minimizing the scratch-building on this helicopter, I limited this only to the engine bay and gearbox, thereby speeding up the process greatly.
So, where do you start with a “straight from the box” build (never done this before)…? Well, apparently on page 1 of the manual. Still waiting on the Verlinden kit, I started putting together all the parts that were separate from the fuselage and interior. I started off by choosing my weaponry options, as the kit came with many, and selected 2 fuel tanks and 2 rocket pods. The pods will be mounted to the wings, one of the tanks will be hanging from the wing by a rope (yes, this is actually done with the real aircraft, too) and the other will be laying on a pallet with some other bits and pieces.
The weapons were followed by the rotorhead and blades, which were slightly altered as I wanted to remove 2 blades and lay them next to the helicopter to create a diorama (my very first one). More on this in a later post once I get going with that. The head itself is pretty detailed and doesn’t need much scratch building at all, just a few wires. The wings were build and most of the nose section followed. Somehow I think Trumpeter made a mistake with the wing molds, as one of them had a completely different shape than the other half, needing some work once put together to make it look decent. The wheels were sanded to create a deflated tire effect, which will later be enhanced one positioned onto the surface of the diorama.
Most work was put into the engine bay and interior. Since I decided to remove one of the engine cowls as well as the engine, the engine compartment needed some serious work. Having found a time lapse video of (I think the Polish Air Force) a maintenance department refitting the gearbox and engines, I got going with adding wires, a gearbox and a firewall. Have a look at the photos for a detailed view of all the work that went into this. The interior from Verlinden needed a lot of sanding and “enhancing” to make it fit. I thought it was a very poor set, but it turns out the real aircraft has many faults and issues in regards to poor fitting of components too. Despite that, the kit needed some extra work to fit inside the fuselage.
It’s safe to say that most work went into the paint job. That’s where my focus would be for this project in an attempt to recreate the weathered look. Having not done a model like this before, I’d be using a lot of new techniques and paints, only to hope it would work as I imagined it would. I started with a layer of primer. Normally I’d do this with the airbrush, but I decided to use spray cans from Tamiya, which actually work really well. Next was pre-shading, using the trusty airbrush with black paint to create panel lines and exhaust traces. The pre-shading was done very thin, which allowed me to follow directly with the next layer, the first camo colour. A green olive-drab colour went on in a random pattern, looking closely at real aircraft and the paint guide that came with the model. What resulted was a pre-shaded aircraft with weird looking green spots all over the place.
The weathered aircraft seem to have a blue-ish look to them, probably due to sunlight. Anyway, I tried recreating this by adding a few drops of blue colour to the grey that would go on next, in an attempt to cover the pre-shading and create a better contrast with the green camo. The lower half was masked off first, as this would remain in the primer-grey colour. I now have a model that looks like it’s new from the factory with some colour-blind person in charge of the paint job… Time for a clear coat to seal it all in.
With the base layers done, I added the decals and another layer of clear coat before starting the weathering process. I started by mixing black, green, and grey paint with thinner to create a wash (roughly 90% thinner). This was painted on with a brush before being absorbed in a random fashion with cotton earbuds and a dry brush. The wash will create a “rain and faded” pattern all over the helicopter. Next I used a sponge to make streaks from top to bottom. As soon as the wash dried, I blended all the colours together by using white oil paints (yes, the extremely bright colour that has nothing to do with a camouflage pattern). By using a sponge again, I rubbed the white paint on mainly the top surfaces, where the camouflage would have faded the most due to sunlight. I then added random spots on the sides before rubbing those out with the sponge again. All the colours were now nicely blended together. Another clear coat before the next step.
What’s an aircraft that’s been outside for 25 years without any rust? Indeed, time to add the rust. Mostly found around the exhausts and engine bays, I used a new product from MIG to create rust effects and streaks, using pigments in the process as well. Guess what, another clear coat after this to finish it off. I removed the masking tape and had a look at the overall result. Not bad, except that the windows are super clean compared to the rest of the model. So, out comes the brush and wash again to solve this issue. The windows were covered with the wash and mostly removed again with the sponge, creating rain streaks at the same time.
So, that’s most of the model done now. All that’s left to do is paint the blades and rotorhead before building the base diorama for the model. This will have to wait however, as I’m packing for my move to Sumburgh in a few weeks. Once I get back to work, I’ll update you on the process of this. Until then!